What is the construction point of steel mixed rope saw?

Release time:

2021-09-29

The steel-mixed rope saw is a cutting and demolition tool for mining, wasteland, Hu ban, large slab stone, thick concrete, irregular concrete steel bars, bridges and roads, etc. Easy to install, flexible use method, can be horizontal shear, vertical shear. The following is the composition of the equipment structure and the differentiated types of wire saws. The composition of the rope saw, rope saw drive, flywheel, guide wheel, rope saw chain (made of diamond material).

What are the construction points of the steel-mixed rope saw? Let's analyze it together.

(1) Fixed steel mixed rope saw and guide wheel

Fix the main and auxiliary legs of the rope saw with M16 chemical anchor bolts. The guide wheel must be installed stably. The edge of the wheel must be aligned with the center line of the rope hole to ensure the effective cutting speed of the cutting surface and strictly implement the installation accuracy requirements.

(2) Set steel mixed rope saw

Please note that according to the determined cutting form, the diamond rope is wound on the driving wheel and the auxiliary wheel in a certain order, so that the direction of the rope is consistent with the driving direction of the driving wheel.

(3) Connection and safety technical measures for operation system of steel-mixed rope saw

According to the on-site conditions, the connection of water, electricity, mechanical equipment and other related pipelines should be accurate and relatively centralized, and the wires should strictly implement the safety operation procedures, so that there are many machines, auxiliary equipment and materials are disorderly, causing accidents. In the process of rope cutting, the direction of rope movement should be protected with a safety protective film, and safety signs should be set up in a certain area to instruct pedestrians not to enter the construction operation area.

(4) Cutting steel mixed rope saw

Start the electric motor, adjust the driving wheel through the wheel to increase the tension, tighten the diamond rope appropriately, provide circulating cooling water, start another electric motor, drive the driving wheel, and guide the diamond rope to rotate and cut. During the cutting process, closely observe the stability of the base and adjust the offset of the guide wheel at any time so that the cutting line is in the same plane.

(5) Selection of steel mixed rope saw cutting parameters

During the cutting process, the cutting parameters are adjusted by operating the wheel to ensure that the running speed of the diamond rope is about 20 m/s. On the other hand, during the cutting process, sufficient cleaning fluid must be ensured to ensure that the diamond rope is cooled and taken away. The grinding debris.

(6) Problems needing attention in the process of cutting steel mixed rope saw

If the occurrence of rope, broken rope and other phenomena, there must be corresponding measures. Security measures need to be strict. Otherwise, the diamond beads on the disconnected diamond rope will fly away and hurt people.

Previous Page: What are the construction requirements of Huisen rope saw

Next Page: Discussion on the Use and Characteristics of Steel-mixed Rope Saw

Huisen rope saw is a cutting equipment driven by a hydraulic power unit, which can cut thick concrete. Is the demolition, maintenance, basement, chimney, column cutting suitable cutting construction equipment.

What are the construction requirements of Huisen rope saw

Huisen rope saw is a cutting and disassembly tool for thick concrete, irregular concrete steel bars, mines, blocks, curved plates, large slabs, bridges and roads. Easy to install, flexible to use, horizontal cutting, vertical cutting. The following can understand the composition of Huisen rope saw equipment structure.

What is the construction point of steel mixed rope saw?

Discussion on the Use and Characteristics of Steel-mixed Rope Saw

According to actual needs and uses, steel-mixed rope saws on the market can be divided into concrete cutting rope saws, granite, mining rope saws, granite wasteland forming rope saws, granite special-shaped processing saws, marble mining rope saws, marble mineral forming rope Saws, marble special-shaped processing rope saws and other 7 categories.

Diamond Segment in Huisen Segment

In the Huisen head is a special diamond head. As a part of the main body of the diamond saw blade, this type of product in Huisen head is made of diamond and matrix binder. As a very hard material, diamond can play the role of cutting edge.

Production Process of Huisen Cutter Head

In the production of Huisen cutter head, the selection of raw materials for the embryo body of Huisen cutter head and the corresponding hot pressing process are quite key steps in the production process. Among them, bronze-based alloy system and the like are selected as the raw materials of ligands. However, the manufacturing cost and use function of the manufacturer cannot achieve the best of both worlds. After horizontal analysis, people have proposed materials made of various alloys as raw materials for the embryo body, after many attempts and applications, we have achieved a more ideal method of cost and function.